Heavy-Duty 10-Inch Grinding Power — The Professional Bench Grinder for Serious Workshop Demands

The ID HBG10DC Electric Bench Grinder is a heavy-duty, stationary 500W bench grinding machine engineered for demanding tool sharpening, deburring, shaping, and surface polishing in professional metalworking workshops, fabrication facilities, and serious DIY environments. Operating on 220–240V at 2,400 RPM and accommodating grinding wheels up to 250mm (10 inches) in diameter, the HBG10DC delivers a significantly larger grinding surface and greater torque than standard 150mm bench grinders — making it the preferred choice for heavy stock removal, large tool restoration, and sustained high-volume grinding. Supplied with a Type G British 3-pin plug for direct UAE and GCC mains compatibility, and featuring a double-insulated body, dual eye shield assemblies, and two sharpening holders, the HBG10DC is built for precision, safety, and long-term workshop reliability.

• 500W Motor at 2,400 RPM for High-Torque, Sustained Grinding Performance: The HBG10DC is driven by a 500W induction motor operating at 2,400 RPM on 220–240V at 50/60Hz — delivering the torque necessary to maintain consistent wheel speed even under heavy material load. The lower RPM compared to smaller bench grinders is intentional: at 250mm wheel diameter, the peripheral surface speed remains high and effective while reducing the risk of overheating tool edges and destroying the temper of hardened steel cutting tools. This makes the HBG10DC ideal for both aggressive stock removal and fine edge sharpening on the same machine.
• 250mm (10-Inch) Maximum Grinding Wheel Diameter for Superior Grinding Surface Area: The HBG10DC's 250mm wheel capacity is a significant step up from standard 150mm or 200mm bench grinders. The larger wheel diameter provides a greater grinding contact area, allowing faster material removal per pass, a flatter grinding surface for more accurate tool sharpening, and a longer wheel service life before replacement is required. This capacity makes the HBG10DC particularly well-suited for large chisels, plane blades, turning tools, and industrial cutting implements that exceed the capacity of smaller machines.
• Double-Insulated Construction for Safe Operation in Conductive Workshop Environments: The double-insulated body ensures complete electrical isolation between all internal components and the outer casing — eliminating the risk of electric shock even in the event of an internal wiring fault. This is especially important for a stationary, mains-powered tool permanently installed in a workshop where metal swarf, coolant, and conductive surfaces are commonplace. Combined with CE certification, the double-insulation design confirms the HBG10DC meets the highest European standards for electrical safety in professional power tools.
• Dual Eye Shield Assemblies for Comprehensive Operator Protection at Both Wheels: The HBG10DC is equipped with two independently mounted eyeshield assemblies — one positioned above each grinding wheel — providing transparent protective barriers that deflect sparks, metal fragments, and abrasive particles away from the operator. Each shield is adjustable to maintain optimal positioning as the wheel wears down over time, ensuring continuous protection throughout the wheel's service life. The dual-shield configuration means both wheels can be used safely without repositioning a single shared guard.
• Two Sharpening Holders for Guided, Repeatable Precision Sharpening on Both Wheels: Unlike many bench grinders that include only a single sharpening holder, the HBG10DC comes with two sharpening holders — one for each wheel. This allows the operator to configure one wheel for coarse grinding and the other for fine sharpening, with a dedicated holder on each side maintaining the correct bevel angle throughout. This dual-holder setup enables a complete coarse-to-fine sharpening workflow without interruption or accessory repositioning.
• Type G British 3-Pin Plug for Immediate UAE and GCC Mains Compatibility: The HBG10DC is supplied with a Type G British 3-pin plug and operates on 220–240V mains power — the standard voltage and plug type used across the UAE, UK, Saudi Arabia, and the wider GCC region. No adapter, transformer, or additional electrical infrastructure is required; the machine connects directly to any standard wall socket and is ready to operate immediately upon secure bench mounting.
• The ID HBG10DC Electric Bench Grinder carries CE certification (machine-level safety testing), confirming it meets European safety and performance standards for stationary professional power tools. It is supplied with a Type G British 3-pin plug for direct compatibility with UAE and GCC mains sockets. The complete kit includes the bench grinder machine, two eyeshield assemblies for dual-wheel spark and debris protection, two sharpening holders for guided precision sharpening at both wheels, and a guide book — providing a fully equipped, ready-to-install grinding solution for professional workshop environments.